Common symbols found when reading pono tenor ukulele tabs

Pono tenor ukulele tabs – There are several techniques specific to playing pono tenor ukulele and other string instruments. These are commonly noted in pono tenor ukulele tabs by capital letters along the staff depicting a ukulele’s strings. Below is a list of the letters used along with a brief description of the technique.

pono tenor ukulele

Hammer On’s in Pono Tenor Ukulele Tab

Capital H designates a hammer on in pono tenor ukulele tab. Guitarists achieve a hammer-on by plucking a string then forcefully pressing a different fret along that string to raise or lower the note’s pitch.

The two numbers right beside each other above the capital H indicates the two notes of the hammer-on. A 0-3 on the third from the bottom line of the staff, for example, would tell a ukulele player to pluck an open D string then quickly press that string on the third fret.

Pull Offs in Pono Tenor Ukulele Tab

A capital P designates a pull off. Players achieve this by plucking a string which is being pressed by one of the fingers of the left hand then quickly pulling that finger off the fret to lower the note’s pitch. The two numbers right beside each other above the capital P indicates the two notes of the pull off.

An 8-6 on the third line from the bottom of the staff, for example, would tell a ukulele player to press the eighth fret of the D string, pluck the string, then quickly pull off with another finger of the left hand ready on the sixth fret.

Slides in Pono Tenor Ukulele Tab

If a ukulele player is supposed to slide a fretting finger either up or down the neck to play a smooth series of notes in one rapid motion this will either be indicated in tab with a capital S or / and \. The slashes are helpful in that they provide a visual depiction of whether the slide is up or down the ukulele’s neck.

pono tenor ukulele

The directions 3S5\3 or 3S5S3 indicates musicians should press the third fret, slide up to the fifth, then back down to the third. When it is unimportant where a slide begins, a number indicating a starting fret may be omitted.

Bends in Ukulele Tab

A letter B in ukulele tab indicates that a pitch is bent on a certain string. To bend a pitch, players pluck a note then use their fretting finger to push the string up or down toward one of the neighboring strings. The farther the string is pushed, the higher the pitch becomes since the player is in effect tightening that one string.

The letter R indicates a return to the string’s original pitch. The instructions 3B{5]R3 means the pitch of a string pressed on the third fret should be bent until it sounds as though the fifth fret is pressed then allowed to return to its regular pitch.

Vibrato in Ukulele Tab

Players can achieve a vibrato affect by quickly bending a pitch up and down. This technique is indicated in tab with a capital letter V.

Muted Strings in Ukulele Tab

An X over one line indicates that that particular string should not be played with the rest of the chord. Several Xs stacked one on top of another indicates a technique called a slap or string click. To achieve this rhythmic effect players lay their fretting hand over the strings and strum.

Taps in Ukulele Tab

A capital T indicates a technique known as tapping, which has some similarities to a hammer-on. In a hammer-on, the right hand strums or plucks a string and then the left hand hammers on a fret. With a tap, the right hand is not involved at all. The left hand strikes the string at the desired fret with enough impact to sound a note.

Now players have all they need to find some tab and start strumming. Musicians interested in learning to read tab may also want to check out the pros and cons of ukulele tab as well as some tab basics covering the staff and numbers.

How to Read Pono Baritone Ukulele Tabs

Songs for ukulele and other string instruments can be written out using standard musical notation, but most players favor learning to read guitar tabs. This form of notation is simple even for self-taught players to decipher and is available for free all across the web. Ukulele tablature does have its limitations, but for someone searching for particular songs on the net or for those teaching themselves to play, tab is a useful tool.

How to Read the Pono Baritone Ukulele Tab Staff

Ukulele tab is so easy to read and understand primarily because it creates a picture of the ukulele’s neck. Tab is written on a staff of six horizontal lines. Each line represents one string of the ukulele.

The bottom line on the staff corresponds to the lowest string, or the E string. The next line up corresponds to the ukulele’s A string. Then comes D, G, B, and high E.

What Numbers Mean When Reading Pono Baritone Ukulele Tab

pono baritone ukulele

The numbers on the staff’s lines indicate which frets, or metal bars beneath the strings, should be pressed. The first fret is the one farthest from the ukulele’s body.

As players start with the first fret, then move to the second, and then continue up the neck, they raise the string’s pitch a half step each time. A 0 in tab indicates an open string, or a string not pressed by any finger.

How to Read Chords in Pono Baritone Ukulele Tab

A stack of six numbers, one on each line, represent a chord. If a player plays each string, pressing the frets indicated, they should hear the chord written above the staff.

If the numbers along the staff aren’t arranged one on top of another, players pluck them separately. Single plucked notes can form arpeggios, or chords played in a series of separate tones rather than simultaneous notes.

Single numbers along the tab staff can also indicate a riff or melody line. In both riffs and arpeggios, musicians often embellish the song by tossing in partial chords every so often. Tab shows this by two or more numbers stacked one on top of each other along the fret.

Turning Pono Baritone Ukulele Tab Into a Song

Chords, arpeggios, and riffs are all building blocks to a song, but without clues as to their rhythm and style, a group of chords written in tab could be the skeleton for any number of songs.

Ukulele tablature is limited in that it has no means of showing how long each string should be allowed to resonate before the next is plucked. Before picking out a song, it can be helpful to have a recording on hand to aid in deciphering the tab.

Furthermore, songs are more than just a cluster of chords. Musicians need to know all the tiny embellishments that breathe personality into a tune. Fortunately, tab does have a way of recording these techniques. Those interested can check out the symbols and letters commonly encountered along the staff indicating hammer on’s, pull offs, bends, vibrato, taps, and more.

Leave a Reply

Your email address will not be published. Required fields are marked *